博文

目前显示的是 一月, 2019的博文

Reasons To Choose Induction Over Hall Effect Sensors

图片
Hall Effect Sensor  are a well-established non-contact detector alternative for many demanding and arduous software. Utilizing semiconductor Hall processors and a magnet attached to a rotating shaft or push pole, the output signal in response to the proximity of the magnet varies and its position can, consequently, be quantified. 1. Because the Inductive sensor is an actual solid-state device, it has no moving parts, bearings or shaft that requires sealing which can subsequently wear or fail. This usually means the inductive device can be set up in the most difficult of environments in which water, dirt, grease, grit, sand and vibration can be encountered which may cause premature failure of mechanical elements. 2. Similarly, since the  Hall IC   utilizes a magnet as its actuator, this makes it vulnerable to interference in magnetised metalwork and electronics, undermining its performance. This susceptibility to magnetic interference isn't shared with the inductive detector, a

The Difference Between Hall Sensor And Hall Transformer

图片
Many times, everyone will think that Hall is the same working principle. In fact, there are many kinds of Hall, such as Hall-type current sensor, Hall transformer , Hall  Magnetic Sensor . Let us understand the difference between the Hall Sensor and the transformer . In fact, the  Hall Sensor  is a Magnetic Sensor. They can be used to detect magnetic fields and their changes, and can be used in a variety of applications related to magnetic fields. Hall devices are based on the  Hall Effect Technology . According to the function of the Hall device, they can be divided into: Hall linear device and Hall switching device. The former outputs an analog quantity, and the latter outputs a digital quantity. According to the nature of the objects being detected, their applications can be divided into direct applications and indirect applications. The former directly detects the magnetic field or magnetic properties of the object to be detected.

Types Of Hall Sensors

图片
Hall Sensors are classified into  Linear Hall Sensors  and Switch Hall Sensors. (1) The switching Hall sensor consists of a voltage regulator, a Hall element, a differential amplifier, a Schmitt trigger and an output stage, which outputs a digital quantity. Switch-type Hall sensors also have a special form called a lock-type Hall sensor. (2) The Linear Hall Sensor consists of a Hall element, a linear amplifier, and an emitter follower, which outputs an analog quantity. Linear Hall sensors can be divided into open loop and closed loop. The closed-loop Hall sensor is also called a zero-flux  Hall sensor . Linear Hall sensors are mainly used for AC and DC current and voltage measurements.  Hall devices have many advantages, they are solid in structure, small in size, light in weight, long in life, easy to install, low in power consumption, high in frequency (up to 1 MHZ), resistant to vibration, not afraid of dust, oil, water vapor and salt spray,contaminated or corroded.

Differential Hall Switch Suits Position Sensing

图片
There's a simple way to measure magnetism with a device called a  Hall Effect Sensor  or probe, which uses a clever bit of science discovered in 1879 by American physicist Edwin H. Hall (1855–1938). Hall's work was ingenious and years ahead of its time—20 years before the discovery of the electron—and no-one really knew what to do with it until decades later when semiconducting materials such as silicon became better understood. These days, Edwin Hall would be delighted to find sensors named for him are being used in all kinds of interesting ways.  Operating from 5 to 36 V, the iC-MZ differential  Hall Switch  with back-end complementary line drivers is designed for gear and pole wheel scanning. The two integrated  Hall Sensors  are set 2 mm apart and sense the difference in magnetic field. The magnetic input frequencies range from dc to 40 kHz, and magnetic dc fields of up to 500 mT are tolerated. At 24 V, a driver current of at least 200 mA can be supplied. Housed in DFN

How To Use Water Flow Sensor?

图片
The  Water Flow Sensor  consists of a plastic valve body, a water rotor and a Hall Effect Sensor. When the water flows through the rotor, rotor rolls and the speed of it changes with a different rate of flow. The hall-effect sensor outputs the corresponding pulse signal. This type of sensor can be found on different diameters, water pressure (MPa) and flow rate (L/m) ranges. Make sure to select one that will cover your needs. The sensor that I have it has 20mm diameter, <1.75Mpa water pressure and ~30 L/m flow rate range. A  Water Flow Meter Sensor  is a device that measures the amount of water flowing through a pipe. There are several water flow meter technologies to choose from depending on the water measurement application, maintenance requirements, and budgetary terms.  Each of these types of water flow meters has a unique principle of operation, specific application benefits, and overall cost-of-ownership. The question is: What water flow meter should you choose for your w