How To Distinguish Between Linear And Switched Hall Sensors?

The Hall IC is divided into two types: linear type and switch type. The output characteristics of the two types of Hall are different. The function of each output pin should be distinguished during detection.
(1) For the linear Hall power supply and the ground ends with 5V DC voltage, the multimeter red and black test leads are respectively connected to the output end and the common ground. Without any magnetic field, the pointer does not move. When the magnetic steel is gradually approached, The pointer gradually deflects and gradually rises, and the amount of pointer deflection is related to the strength of the magnetic field.
The Linear Hall Sensor is used for speed control on electric bicycles.
(2) Switch-type Hall is characterized by switching characteristics, only on and off, no pointer rises and falls, the magnetic field S is strong enough, Hall is turned on, and the magnetic field has two results: 1 Latch Hall Switch IC is still in the on state after the magnetic field is removed. Only when the phase N pole appears, the Hall is turned off. 2 The non-latching Hall is turned on when the magnetic field strength is sufficient, and is cut off when the magnetic field is gone. .
The former measures the position of the magnetic field for the brushless motor, and the latter is used for the mechanism such as the brake power-off switch and the false assist force, and the vehicle mileage speed sensor.
The switch type Hall is also divided into three types: normally open type, normally closed type, and bistable output.
(3) A magnetic steel and a multimeter should be prepared during the test, set in the DC 5^-10V file, the red pen is connected to the output pin, and the black test pen is grounded.
For Linear Sensor, when the magnetic steel is close, the output voltage will gradually rise or fall, indicating that the foot is connected correctly; if there is no output, you can change the pin and try again. If several changes are not made, the Hall damage is invalid. .
If the magnetic steel is close to the Hall sensor, the pointer of the multimeter is immediately moved into position, and does not change gradually with the approach and distance of the magnetic steel, even after the removal of the magnetic steel, only when the other side of the magnetic steel is close. The change indicates that the Hall sensor is a switch type and is a latch type, which is a position sensor of the brushless motor.
Linear Hall Sensor

评论

发表评论

此博客中的热门博文

Omnipolar Hall IC

图片
  Omnipolar Hall IC The omnipolar Hall-effect sensor  includes the following on a single silicon chip: reverse voltage protector, voltage regulator, temperature compensation circuit, Hall-voltage generator, signal amplifier, Schmitt trigger and open-drain output driver, etc. Produced with CMOS technology, an omnipolar Hall IC is asked for lower supply voltage and less power supply. It is available in two package types: SOT-23-3L (Type M) and TO-92UA (Type UA). More detail of China Hall Sensor , please via: https://www.ahest.net/
阅读全文

Method Of Detecting Switch Type Hall Sensor

图片
In the use of hall sensor for maintenance machinery, we will encounter holzer not working, from holzer's shape can not distinguish whether the holzer element is damaged, and how to detect whether the switch type of hall sensor is damaged. Taking Holzer YS282 as an example, the test method of switch type Holzer element is as follows: First, find a resistance R of 1K Omega, which is connected to the figure 1 and 3 feet, and connect the positive pole of the DC power of the 12V to the foot of the  switch type hall sensor YS282, and the anode is connected to the foot. The multimeter is placed in a DC 50V file, the red pen is connected to the foot, and the black pen is connected to the foot, and the pointer changes of the multimeter are observed. When the magnet N is very close to the test point of the hall sensor YS282, the pointer of the multimeter is deflected from the high level to the low level; when the N pole of the magnet is far away from the test point of the Holzer element Y
阅读全文

How To Use Water Flow Sensor？

图片
The  Water Flow Sensor  consists of a plastic valve body, a water rotor and a Hall Effect Sensor. When the water flows through the rotor, rotor rolls and the speed of it changes with a different rate of flow. The hall-effect sensor outputs the corresponding pulse signal. This type of sensor can be found on different diameters, water pressure (MPa) and flow rate (L/m) ranges. Make sure to select one that will cover your needs. The sensor that I have it has 20mm diameter, <1.75Mpa water pressure and ~30 L/m flow rate range. A  Water Flow Meter Sensor  is a device that measures the amount of water flowing through a pipe. There are several water flow meter technologies to choose from depending on the water measurement application, maintenance requirements, and budgetary terms.  Each of these types of water flow meters has a unique principle of operation, specific application benefits, and overall cost-of-ownership. The question is: What water flow meter should you choose for your w
阅读全文