Linear Hall effect sensors

Linear Hall effect sensors
Linear Hall Sensor will pass linear area /nonlinear area/ saturation area during the magnetic induction increases. When there is no magnetic field that applies in sensor (B=0), when the output voltage of sensor is only half of Vcc (Vcc/2); when “N” pole faces mark surface of sensor, and be closed to it gradualy (B→-∞）,the output voltage begins to decrease, and the voltage doesn’t reduce with the increased magnetic field; When the “S” pole of magnet faces the mark surface of the sensor and is closed to sensor gradualy （B→+∞）, the output voltage of sensor begins to increase, and it doesn’t increase with the increased magnetic field after it reaches saturation voltage.The magnetic and electric transfer characteristic curve of linear sensor is shown as the figure:
Hall Effect Sensor Features
Rated working voltage 4.5 V ~ 6 V;
Operating temperature range: -40℃ ~ 125℃;
Rail to Rail voltage output, Rated output current : 6 mA;
Variety of package forms and outer packings for your choice;
No mechanical contact, no spark, switch signal stability, no shaking moment, high reliability and safety;
Products meet the EU RoHS instruction 2011/65 / EU and REACH regulations 1907/2006 / EU requirements.
https://www.ahest.net/hall-switch/linear-hall-sensor.html

评论

发表评论

此博客中的热门博文

Omnipolar Hall IC

图片
  Omnipolar Hall IC The omnipolar Hall-effect sensor  includes the following on a single silicon chip: reverse voltage protector, voltage regulator, temperature compensation circuit, Hall-voltage generator, signal amplifier, Schmitt trigger and open-drain output driver, etc. Produced with CMOS technology, an omnipolar Hall IC is asked for lower supply voltage and less power supply. It is available in two package types: SOT-23-3L (Type M) and TO-92UA (Type UA). More detail of China Hall Sensor , please via: https://www.ahest.net/
阅读全文

Method Of Detecting Switch Type Hall Sensor

图片
In the use of hall sensor for maintenance machinery, we will encounter holzer not working, from holzer's shape can not distinguish whether the holzer element is damaged, and how to detect whether the switch type of hall sensor is damaged. Taking Holzer YS282 as an example, the test method of switch type Holzer element is as follows: First, find a resistance R of 1K Omega, which is connected to the figure 1 and 3 feet, and connect the positive pole of the DC power of the 12V to the foot of the  switch type hall sensor YS282, and the anode is connected to the foot. The multimeter is placed in a DC 50V file, the red pen is connected to the foot, and the black pen is connected to the foot, and the pointer changes of the multimeter are observed. When the magnet N is very close to the test point of the hall sensor YS282, the pointer of the multimeter is deflected from the high level to the low level; when the N pole of the magnet is far away from the test point of the Holzer element Y
阅读全文

How To Use Water Flow Sensor？

图片
The  Water Flow Sensor  consists of a plastic valve body, a water rotor and a Hall Effect Sensor. When the water flows through the rotor, rotor rolls and the speed of it changes with a different rate of flow. The hall-effect sensor outputs the corresponding pulse signal. This type of sensor can be found on different diameters, water pressure (MPa) and flow rate (L/m) ranges. Make sure to select one that will cover your needs. The sensor that I have it has 20mm diameter, <1.75Mpa water pressure and ~30 L/m flow rate range. A  Water Flow Meter Sensor  is a device that measures the amount of water flowing through a pipe. There are several water flow meter technologies to choose from depending on the water measurement application, maintenance requirements, and budgetary terms.  Each of these types of water flow meters has a unique principle of operation, specific application benefits, and overall cost-of-ownership. The question is: What water flow meter should you choose for your w
阅读全文