How to Use the Sensor Correctly?

 As a Bipolar Hall IC China Factory, share with you. Before using the sensor and Hall sensor, be sure to verify the working power supply voltage level and whether the measurement range is consistent with the measured signal! Avoid misuse and mixing of different voltages.

In order to facilitate the reference, the following discusses the correct use of the sensor from several aspects.

1. Use environment

Sensor and Hall sensor should be free from conductive dust, metal corrosive and insulating gas. Otherwise, a secondary circuit will occur due to conductive dust and objects, or a short circuit between the secondary side power supply and the signal will burn out the sensor.

1.1 Ambient temperature

The sensor's specifications will stipulate the normal working ambient temperature range of the sensor, such as -40 to 85 degrees, depending on the product model. It is recommended not to exceed the temperature range specified in the specification, or exceed the normal operating temperature range of the sensor. Some internal components will degrade performance due to temperature characteristics, reduce accuracy, output signal inaccuracy, or fail to work.

The sensor should be installed as far as possible in a place with good ventilation and heat dissipation, so as to avoid excessive temperature affecting the measurement accuracy and life of the sensor.

1.2 Altitude

Generally, the altitude is considered when the sensor is designed, and it is usually 2000 meters. However, it is not only suitable for altitudes below 2000 meters. If the altitude exceeds 2000 meters in actual use, it will mainly affect the heat dissipation and insulation performance of the sensor. Will reduce the insulation characteristics, although the insulation can also be improved by external means, but it is difficult to achieve and increase the cost. The heat dissipation problem can be solved relatively easily by means such as forced air cooling.

1.3 Installation location

Since the sensor is a non-contact measurement, most of it detects the magnetic field around the charged conductor, so it is not suitable to have a strong magnetic field near the sensor and a device that easily generates a magnetic field. Including transformers, reactors and conductors that flow large, etc. Especially in the three-phase test, adjacent sensors should not be installed too close. Where space permits, the spacing should be as large as possible.

Sometimes limited by the cabinet and its internal layout, it is difficult to leave enough space. In this case, it is recommended that the sensor be installed in a wrong position, especially for the HALL principle sensor. The position of the HALL device should be the magnetic field source as much as possible.

Our company also has Micropower Hall Sensor on sale, welcome to contact us.

评论

发表评论

此博客中的热门博文

Omnipolar Hall IC

图片
  Omnipolar Hall IC The omnipolar Hall-effect sensor  includes the following on a single silicon chip: reverse voltage protector, voltage regulator, temperature compensation circuit, Hall-voltage generator, signal amplifier, Schmitt trigger and open-drain output driver, etc. Produced with CMOS technology, an omnipolar Hall IC is asked for lower supply voltage and less power supply. It is available in two package types: SOT-23-3L (Type M) and TO-92UA (Type UA). More detail of China Hall Sensor , please via: https://www.ahest.net/
阅读全文

Method Of Detecting Switch Type Hall Sensor

图片
In the use of hall sensor for maintenance machinery, we will encounter holzer not working, from holzer's shape can not distinguish whether the holzer element is damaged, and how to detect whether the switch type of hall sensor is damaged. Taking Holzer YS282 as an example, the test method of switch type Holzer element is as follows: First, find a resistance R of 1K Omega, which is connected to the figure 1 and 3 feet, and connect the positive pole of the DC power of the 12V to the foot of the  switch type hall sensor YS282, and the anode is connected to the foot. The multimeter is placed in a DC 50V file, the red pen is connected to the foot, and the black pen is connected to the foot, and the pointer changes of the multimeter are observed. When the magnet N is very close to the test point of the hall sensor YS282, the pointer of the multimeter is deflected from the high level to the low level; when the N pole of the magnet is far away from the test point of the Holzer element Y
阅读全文

How To Use Water Flow Sensor？

图片
The  Water Flow Sensor  consists of a plastic valve body, a water rotor and a Hall Effect Sensor. When the water flows through the rotor, rotor rolls and the speed of it changes with a different rate of flow. The hall-effect sensor outputs the corresponding pulse signal. This type of sensor can be found on different diameters, water pressure (MPa) and flow rate (L/m) ranges. Make sure to select one that will cover your needs. The sensor that I have it has 20mm diameter, <1.75Mpa water pressure and ~30 L/m flow rate range. A  Water Flow Meter Sensor  is a device that measures the amount of water flowing through a pipe. There are several water flow meter technologies to choose from depending on the water measurement application, maintenance requirements, and budgetary terms.  Each of these types of water flow meters has a unique principle of operation, specific application benefits, and overall cost-of-ownership. The question is: What water flow meter should you choose for your w
阅读全文